After receive Dr.wellness hydrogen inhalation machine（new YL-3000）， what should you do ?

First, thank you choose Dr. wellness hydrogen inhalation.
When using the machine for the first time, pls notice the following:
Prohibit:
Do not use in confined spaces!
Flammable gas, no ignition test!
Do not block the gas outlet when the machine is running!
Reminder: Please unplug the plugs of H and O outlets before turning on the machine.

Warning: Keep the machine away from open flame while operating. Pause or power off the unit when leaving it unattended.

Maintenance: Please use only TDS‑0 distilled water. Great Value brand distilled water has received positive feedback from our other US customers and is available for US clients to purchase.

Do not use a household water distiller to make homemade distilled water. Water produced at home does not meet the required purity standard.

For Asia, we recommend Watsons distilled water, C'estbon and Wahaha purified water.
For the USA, we recommend Great Value TDS‑0 distilled water.

Water with fewer impurities will deliver better machine performance and extend service life.
You may purchase TDS‑0 distilled water from local stores or online shops.

If qualified water is added in accordance with requirements, almost no after‑sales maintenance will be needed.

For new machines: Add water and let the unit soak for 20 minutes. (The hydrogen‑oxygen generator is drained before shipment, so the internal proton membrane stays dry during transportation. After receiving the device, first press the "Add Water" button to fill the reservoir. Do not operate the machine right away. Let it soak for 20 minutes to ensure the proton membrane fully absorbs water before power‑on.)

Once soaking is finished, simply press the Start button. There is no need to pour out the soaking water.

The YL-3000 operate video as following, you can look at and follow it:

How To Use:

1.Turn on the power, connect the water pipe.

Press the gray clamp with one finger and remove the plug with the other hand( remeber one finger must press the gray clamp)After removing the plug, insert the water supply pipe firmly into the tank and put the other end into purified water or distilled water (TDS=0).

3.Press the water adding button on the screen, it will add water automatically.

2.Timing function：press the plus and minus signs . You can set it for 1-8 hours.

3.The Flow Rrate Range: press the plus and minus signs on the right to adjust the flow rate from 1500ml to 3000ml. There are 16 gears to adjust.

4. One person inhales the H2&O2 Connection

First connect the Y tube then  connect the cannular like following, then you can inhale the H2&O2 now.

5.Two people inhale together

Use" Y "connector and "T" connector to connect the nasal cannular on both sides like following,then two people can inhale hydrogen at the same time

6.Make hydrogen water 

Use a tube, one end connect to H2 outlet, the other end connect into Hydrogen dissolved rod, leave the O2 output open, put rod into water, after 5-7 minutes later, can drink the hydrogen water.

7. Drain Water Connect the drain pipe.

Unplug the add water pipe and plug it with the original plug (when pulling it out, remember to press the gray retaining spring with one finger while pulling it out).

Use the same method to remove the drain pipe plug and install the drain pipe，the drain pipe the other end put it in a container ，then press the "drain water" botton on the screen， It will drain water automatically.（Please note that the drained water cannot be reused）.

Other Customer FAQs

1.How to turn off the light of the Dr.wellness YL-3000 hydrogen generator?

Press and hold the light bulb button in the upper left corner to enter night mode, and the screen and the light of the slippery cup will be turned off.        

2.how to use the water collector of the hydrogen inhaler?

Pls check this video: https://youtube.com/shorts/MxDUHisZACc?si=DbF0E3iUXllx1uSM